twilkers Senior Member Joined: 12 Dec 2010 Posts: 13 Location: bay area, CA Expertise: Just starting
Posted Sun Nov 11, 2012, 8:59am Subject: rancillio silvia, weak steamer
had our silvia for a couple years now, awesome machine. this morning the steaming was weak and I smelled a burnt odor. the water was very low so I filled it up. the steamer didn't come back to full strength and the steamed milk tasted burnt.
can someone guide me through the troubleshooting? I'm thinking heating element, maybe thermostat.
D4F Senior Member Joined: 15 Mar 2012 Posts: 1,189 Location: USA Expertise: I like coffee
Espresso: Gaggia Classic PID Grinder: Preciso
Posted Sun Nov 11, 2012, 1:50pm Subject: Re: rancillio silvia, weak steamer
Burnt odor and taste, and weak steam seem like a wand that is partially clogged with milk. Take off the tip and try a pipe cleaner in the tube and soak the tip. You can remove the wand to clean. Milk can get up into the wand, especially if you allow cooling belore cleaning.
Bad tstat should not smell/taste. Bad element will often trip GFI. Start with the wand and report back.
cleaned wand and replaced. got some stuff out. fired it up this morning, after steam light is off, steam is still weak and burnt odor remained.
additional observation is that the steam pressure degrades quickly (much quicker than before) and the light never comes on as it used to (as the pressure decreased). sort of seems like a temp sensor is not kicking on the heating element or the element cannot deliver the heating capacity it used to.
Your comment about the water being very low, points to the possibility of a partially melted heater. Just a random thought. The heaters are easily damaged with low water levels, this could lead to the burnt smell. Or not, check everything and rule out what does not fit.
In real life, my name is Wayne P.
Feed the newbs, starve the trolls and above all enjoy what you drink!
Wayne, I felt the same way about Bush W. and still do .but I did not see fit to shove my political views down your throat.But since you brought it up I will just point out democracy is hard when you disagree with the currant elected party,but that doesnt make the other guy a tyrant ,an American President ,by the way is in no position to ever be a tyrant , .And oh yeh I agree with you ,it sounds like low water levels may have damaged the heating coil . Don
Based on what you've reported, I am still leaning toward a plumbing problem.
The fact that the steam light does not turn back on suggests to me that the temperature/pressure inside the boiler are probably OK. But replacing the steam thermostat is easy and cheap so might be worth trying as a troubleshooting step.
If your machine is not on a GFI-protected circuit, then I would strongly suggest fixing that situation right away. If the element is burnt out, a GFI will normally flag this for you immediately. It might also protect you from a nasty shock if live AC is reaching the machine frame from an exposed nichrome wire inside the boiler.
How long between flipping on the steam switch and steaming temperature reached (indicated by the light turning off)? My experience is that this takes around 90 seconds if everything is working OK.
I think Jim has the most logical diagnoses on this one ,I jumped on the low boiler trail and overlooked the obvious . Experience is everything .Im lucky to still be on my original sensors after so many years.Much better to have to replace a sensor than a boiler ,thats for sure. Don
ok, during the post descaling purge, I noted something again. I was running water through the steamer to get rid of that funky smell/taste so let steam run for a long time. it would almost run out of steam with significantly reduced pressure and the heat light would not come on.
there is a faint ordor, not sure if it's burnt or metallic.
I was running water through the steamer to get rid of that funky smell/taste so let steam run for a long time. it would almost run out of steam with significantly reduced pressure and the heat light would not come on.
How long steaming, or how much water steamed out? If you get the water down far enough, you could be overheating the element I believe. Are you talking longer than normal use? I would ask you to reproduce and then fill it with water with the wand open and running the pump. Time the fill. The pumps will run about 10cc/sec unobstructed, and you get an idea of how empty the boiler was. I can't advise repeating and risk running it low, but if you find yourself is a similar low steam circumstance, check the fill time.
As far as running water through the steamer, just run the pump with the wand open as opposed to prolonged steaming to low water.
Symbols: = New Posts since your last visit = No New Posts since last visit = Newest post
Forum Rules: No profanity, illegal acts or personal attacks will be tolerated in these discussion boards. No commercial posting of any nature will be tolerated; only private sales by private individuals, in the "Buy and Sell" forum. No cross posting allowed - do not post your topic to more than one forum, nor repost a topic to the same forum. Who Can Read The Forum? Anyone can read posts in these discussion boards. Who Can Post New Topics? Any registered CoffeeGeek member can post new topics. Who Can Post Replies? Any registered CoffeeGeek member can post replies. Can Photos be posted? Anyone can post photos in their new topics or replies. Who can change or delete posts? Any CoffeeGeek member can edit their own posts. Only moderators can delete posts. Probationary Period: If you are a new signup for CoffeeGeek, you cannot promote, endorse, criticise or otherwise post an unsolicited endorsement for any company, product or service in your first five postings.