Posted Wed Mar 6, 2013, 12:25pm Subject: Re: E61 Rocket - No water from wand...
The valve itself should be removed and overhauled. it is probably either full of crud, scale, or maybe the stop gasket has failed. A machine that old and left in that poor of condition would prompt me to fully disassemble and clean before use. If the machine seems to be functioning otherwise (pump works, brew pressure OK, water gets hot, and the machine producers steam) then overhaul kits for both valves and a full kit to overhaul the group would probably be a good investment.
cant help you out on a step by step, but these machines generally are pretty straight forward i think. Just take a ton of pictures and keep everything in order so you can put it back in the reverse. what i typically do is go step by step and take a picture before removing everythign...and when i remove it i keep all the parts, etc in order.
one easy way (i did last time i did a complete dissasemble) is to use a spare table or countertop. the first stuff you take off the machine go on the far left and each step you put the next pieces to the right. i actually put a piece of tape between each step which roughly matched up with photos. as you remove items that need to be cleaned just keep them in the right spot.
after its all taken apart, remove each individual item till you are satisfied and then start assembing in order with the aid of your photos.
my tip - take lots of photos from different angles, especially of any wiring!
SStones Senior Member Joined: 24 Nov 2012 Posts: 455 Location: Canada Expertise: Professional
Espresso: Giga 5, ECM Giotto, Rocket... Grinder: Anfim Milano-Best Vac Pot: No :( Drip: Some $30 thing from Walmart Roaster: I buy pre-roasted.
Posted Wed Mar 6, 2013, 8:09pm Subject: Re: E61 Rocket - No water from wand...
I figure it is either less than 10 years old, or perhaps an ECM rather than a Rocket. Regardless, the valves themselves should be nearly identical side to side, so re-assembly is as simple as making sure it is the same as the untouched one. As for the valces, they differ greatly from era to era, so I don't know which you may have, but go ahead and take it apart, clean it and reassemble it. It will either fix it or make the specific problem obvious. If you post a picture of the machine, centering on the external part of the hot-water valve, I could offer more encouragement.
Posted Sat Mar 9, 2013, 12:10pm Subject: Re: E61 Rocket - No water from wand...
Hi there, as your Rocket/ECM is 8-10 years old, i'm guessing you have the older type valves where the steam and water wand are not attached to the valves, ie; they exit the machine faceplate below the valve from a separate hole? There is surprisingly little info around about servicing these valves, as i think most Rocket owners just put their machines in to be serviced. Here's an older thread which shows the valve dis-assembled;
If the problem is in the valve shaft seal, they are not easily replaceable, you are better off replacing the whole valve shaft.Coffeeparts in Aussie sell some ECM/Rocket parts, but i can't tell from their diagram whether its for the old or new style valves;
Symbols: = New Posts since your last visit = No New Posts since last visit = Newest post
Forum Rules: No profanity, illegal acts or personal attacks will be tolerated in these discussion boards. No commercial posting of any nature will be tolerated; only private sales by private individuals, in the "Buy and Sell" forum. No SEO style postings will be tolerated. SEO related posts will result in immediate ban from CoffeeGeek. No cross posting allowed - do not post your topic to more than one forum, nor repost a topic to the same forum. Who Can Read The Forum? Anyone can read posts in these discussion boards. Who Can Post New Topics? Any registered CoffeeGeek member can post new topics. Who Can Post Replies? Any registered CoffeeGeek member can post replies. Can Photos be posted? Anyone can post photos in their new topics or replies. Who can change or delete posts? Any CoffeeGeek member can edit their own posts. Only moderators can delete posts. Probationary Period: If you are a new signup for CoffeeGeek, you cannot promote, endorse, criticise or otherwise post an unsolicited endorsement for any company, product or service in your first five postings.