acodring Senior Member Joined: 15 Jun 2012 Posts: 7 Location: Ottawa Expertise: I like coffee
Espresso: Quick Mill Andreja Grinder: Baratza Vario
Posted Tue May 20, 2014, 8:35am Subject: Pressure gauge stuck on Quick Mill Andreja - repair or replace?
Hi there, I was a little slow getting around to a descale recently and my Andreja expressed it's frustration with me by blowing it's top.
I believe what happened is the p-stat got sticky, the boiler overheated, and the boiler release valve released. I wasn't in the room, but heard the bang from the other side of the house. This has happened before, and the machine gets back to normal after a descale.
This time the machine mostly recovered and works normally, except for the boiler pressure gauge which is stuck on the wrong side of the zero pin. See attached photo.
I did some searching here and saw a recommendation to replace the gauge in another thread but that was for a different machine.
Would that same advice apply to my Andreja, or is there some kind of repair I can attempt? I'm a capable instruction-follower, and have successfully torn down and rebuilt the group before.
calblacksmith Moderator Joined: 25 Nov 2007 Posts: 8,025 Location: Riverside, Ca, U.S.A. Expertise: I live coffee
Espresso: ECM Vene. A1, La Cimbali M32 Grinder: Azkoyen Capriccio, Major Vac Pot: 40s era Silex Drip: Msl. Com. brewers Roaster: gave it a try, decided no
Posted Tue May 20, 2014, 1:10pm Subject: Re: Pressure gauge stuck on Quick Mill Andreja - repair or replace?
For the most part, the gauges are not repairable but you have nothing to loose. It kind of depends on what is wrong with the gauge. If it is simply that it bounced over the pin and is now stuck, you might be able to remove the glass and pop the needle over the pin. If however the boron tube inside the gauge is bent an this is now the normal position for the needle, you need to replace the gauge.
It is up to you. The machine can work just fine without the gauge so even if you do nothing you still can have coffee. Be aware though that some of the fittings are metric in the plumbing (I am not sure with your machine about the gauge) and if you remove the gauge and can not get it to seal again then you will be without coffee until you can get a cap for the line or the gauge is replaced.
In real life, my name is Wayne P. Anything I post is personal opinion and is only worth as much as anyone else's personal opinion. YMMV!
Feed the newbs, starve the trolls and above all enjoy what you drink!
skydragondave Senior Member Joined: 18 Feb 2013 Posts: 168 Location: Ontario, Canada Expertise: Professional
Espresso: Commercial Only Grinder: Commercial Only Roaster: Has Garanti HG5
Posted Wed May 21, 2014, 5:52pm Subject: Re: Pressure gauge stuck on Quick Mill Andreja - repair or replace?
If you are in Ottawa, there are a few sources in Montreal that can probably get this gauge to you faster and cheaper. My first recommendation would be Cafe Union - they are a Quickmill dealer. Speak to James in the parts department, he speaks perfect English and is very knowledgeable. If you can't get one from him email me and I'll send you the contact info of a few others. If the needle is on the other side of the pin, one of two things happened - the bourdon tube overinflated and distorted, or the linkage between the bourdon tube and the needle broke away. Neither are repairable and for the cost of a new gauge, isn't worth the effort especially since you will have no way to calibrate the needle position and rate.
Symbols: = New Posts since your last visit = No New Posts since last visit = Newest post
Forum Rules: No profanity, illegal acts or personal attacks will be tolerated in these discussion boards. No commercial posting of any nature will be tolerated; only private sales by private individuals, in the "Buy and Sell" forum. No SEO style postings will be tolerated. SEO related posts will result in immediate ban from CoffeeGeek. No cross posting allowed - do not post your topic to more than one forum, nor repost a topic to the same forum. Who Can Read The Forum? Anyone can read posts in these discussion boards. Who Can Post New Topics? Any registered CoffeeGeek member can post new topics. Who Can Post Replies? Any registered CoffeeGeek member can post replies. Can Photos be posted? Anyone can post photos in their new topics or replies. Who can change or delete posts? Any CoffeeGeek member can edit their own posts. Only moderators can delete posts. Probationary Period: If you are a new signup for CoffeeGeek, you cannot promote, endorse, criticise or otherwise post an unsolicited endorsement for any company, product or service in your first five postings.